What is dynamic range in vibration testing?

Dynamic range represents the ratio between the largest and smallest signals that can be accurately measured and controlled simultaneously. It is expressed in decibels (dB) and defines the span from the system's maximum signal handling capability down to the noise floor. For vibration testing, dynamic range determines the ability to measure both high-amplitude signals at resonances and low-amplitude signals at anti-resonances within the same test.

Why is 24-bit ADC dynamic range only 110 dB instead of 144 dB theoretical?

While a 24-bit ADC theoretically provides 144 dB dynamic range (20*log10(2^24)), practical systems achieve only 100-110 dB due to multiple factors: accelerometer self-noise (0.0001 g typical), signal conditioning noise, ADC effective number of bits (20-21 ENOB vs 24 theoretical), environmental electromagnetic interference, thermal noise, ground loops, cable triboelectric noise, and crest factor requirements for random vibration. These factors accumulate to establish a much higher practical noise floor than theoretical calculations suggest.

What factors limit dynamic range in vibration control systems?

Dynamic range is limited by: (1) Accelerometer self-noise and maximum output, (2) Signal conditioning amplifier noise and gain limitations, (3) ADC quantization noise and effective resolution (ENOB), (4) Environmental EMI and RFI interference, (5) Ground loops and common impedance coupling, (6) Cable triboelectric noise and capacitance, (7) Thermal noise from resistive elements, (8) Channel-to-channel crosstalk, (9) Building vibration and seismic background noise, (10) Crest factor requirements reserving headroom for peaks.

How can I improve dynamic range in my vibration test system?

Improve dynamic range through: (1) Use low-noise accelerometers with <0.00005 g noise floor, (2) Optimize gain settings to use maximum ADC range without overload, (3) Implement proper grounding with single-point signal grounds, (4) Use high-quality shielded cables with minimal triboelectric noise, (5) Route signal cables away from power lines and EMI sources, (6) Apply appropriate filtering to remove out-of-band noise, (7) Control laboratory temperature and minimize thermal effects, (8) Use spectral averaging to reduce random noise (10 dB improvement with 100 averages), (9) Select appropriate full-scale ranges for each channel, (10) Implement environmental EMI shielding and acoustic treatment.

What is effective number of bits (ENOB) for vibration testing ADCs?

ENOB describes actual resolution achieved by a real ADC considering noise, distortion, and non-idealities. A 24-bit ADC typically achieves 20-21 effective bits under good conditions, corresponding to approximately 120-126 dB dynamic range. This reduction from theoretical 144 dB results from ADC thermal noise, quantization noise, integral and differential nonlinearity, and aperture jitter in sample-and-hold circuits.

What dynamic range is achievable in practical vibration testing?

Realistic achievable dynamic range in well-configured vibration test systems is 100-110 dB. This accounts for accelerometer noise (0.0002-0.0003 g noise floor), signal conditioning contributions, environmental interference in typical industrial laboratories, crest factor headroom for random vibration (12 dB), and channel crosstalk limitations. Specialized low-noise systems with extensive averaging and environmental control can achieve 110-120 dB, while challenging conditions may reduce performance to 80-90 dB.

How does PANTHER achieve >110 dB dynamic range?

PANTHER achieves >110 dB input dynamic range through: (1) True 24-bit ADCs with low noise and high ENOB performance, (2) Eight auto-ranging voltage ranges (±12V to ±0.5V) optimizing signal levels, (3) Low-noise signal conditioning with <2 µV RMS amplifier noise, (4) High-quality anti-aliasing filters minimizing noise contribution, (5) Simultaneous sampling eliminating multiplexer crosstalk, (6) <-100 dB channel-to-channel crosstalk specification, (7) Digital calibration and offset removal, (8) Superior grounding and shielding design, (9) 262,144 samples/second enabling fine frequency resolution, (10) Advanced digital filtering and averaging capabilities.

Search Results | Spectral Dynamics

Name: PANTHER Vibration Control System
Brand: Spectral Dynamics
Availability: InStock

Spectral Dynamics, Inc. is a leading worldwide supplier of systems and software for vibration testing, structural dynamics, and acoustic analysis. Spectral Dynamics' products are used for design verification, product testing and process improvement by manufacturers of all types of electronic and mechanical products.

2199 Zanker Road, San Jose, CA 95131-2109
Tel: (800) 778-8755
sales@spectraldynamics.com
service@spectraldynamics.com

Buyer’s Guide: Choosing a Comprehensive Vibration Control & Analysis System

CATS - The Computer-Aided Test Suit

CATS Modal / STAR Modal - FAQs

Domestic US Service

Dynamic Range Considerations in Vibration Testing: Complete Technical Guide to ADC Performance, Noise Floor Analysis, and System Optimization

Lynx

Panther

Puma Vibration Control and Analysis System

STAR - Modal Analysis

STAR Acoustics

Upcoming Tradeshows

Vibration Controllers

Advanced Solutions

Support

Shakers

Options

Multiple/Single Axis

Single Axis

ARPG Products

P.I.N.D. System

Advanced Solutions

High Speed Data Acquisition

Data Analysis

Service & Information

Software Support

Additional Support

Vibration Controllers

Advanced Solutions

Support